(PHP 5 >= 5.4.0, PHP 7, PHP 8)
SNMP::set — Set the value of an SNMP object
Requests remote SNMP agent setting the value of
one or more SNMP objects specified by the objectId.
If objectId is string, both
type and value must be
string too. If objectId is array
value must be equal-sized array containing
corresponding values, type may be either
string (it's value will be used for all
objectId-value pairs) or
equal-sized array with per-OID value. When any other parameters' combinations are
used, a number of E_WARNING messages may be shown with detailed description.
objectIdThe SNMP object id
When count of OIDs in object_id array is greater than max_oids object property set method will have to use multiple queries to perform requested value updates. In this case type and value checks are made per-chunk so second or subsequent requests may fail due to wrong type or value for OID requested. To mark this a warning is raised when count of OIDs in object_id array is greater than max_oids.
typeThe MIB defines the type of each object id. It has to be specified as a single character from the below list.
| = | The type is taken from the MIB |
| i | INTEGER |
| u | INTEGER |
| s | STRING |
| x | HEX STRING |
| d | DECIMAL STRING |
| n | NULLOBJ |
| o | OBJID |
| t | TIMETICKS |
| a | IPADDRESS |
| b | BITS |
If OPAQUE_SPECIAL_TYPES was defined while compiling the SNMP library, the following are also valid:
| U | unsigned int64 |
| I | signed int64 |
| F | float |
| D | double |
Most of these will use the obvious corresponding ASN.1 type. 's', 'x', 'd' and 'b' are all different ways of specifying an OCTET STRING value, and the 'u' unsigned type is also used for handling Gauge32 values.
If the MIB-Files are loaded by into the MIB Tree with "snmp_read_mib" or by specifying it in the libsnmp config, '=' may be used as
the type parameter for all object ids as the type can then be automatically read from the MIB.
Note that there are two ways to set a variable of the type BITS like e.g. "SYNTAX BITS {telnet(0), ftp(1), http(2), icmp(3), snmp(4), ssh(5), https(6)}":
See examples section for more details.
valueThe new value.
This method does not throw any exceptions by default.
To enable throwing an SNMPException exception when some of library errors occur
the SNMP class parameter exceptions_enabled
should be set to a corresponding value. See
SNMP::$exceptions_enabled explanation for more details.
Example #1 Set single SNMP object id
<?php
$session = new SNMP(SNMP::VERSION_2C, "127.0.0.1", "private");
$session->set('SNMPv2-MIB::sysContact.0', 's', "Nobody");
?>Example #2 Set multiple values using single SNMP::set() call
<?php
$session = new SNMP(SNMP::VERSION_2C, "127.0.0.1", "private");
$session->set(array('SNMPv2-MIB::sysContact.0', 'SNMPv2-MIB::sysLocation.0'), array('s', 's'), array("Nobody", "Nowhere"));
// or
$session->set(array('SNMPv2-MIB::sysContact.0', 'SNMPv2-MIB::sysLocation.0'), 's', array("Nobody", "Nowhere"));
?>Example #3 Using SNMP::set() for setting BITS SNMP object id
<?php
$session = new SNMP(SNMP::VERSION_2C, "127.0.0.1", "private");
$session->set('FOO-MIB::bar.42', 'b', '0 1 2 3 4');
// or
$session->set('FOO-MIB::bar.42', 'x', 'F0');
?>