If you receive an error like:
Warning: ftp_nb_put(): Unable to service PORT commands in /path/to/file.php on line 27
verify whether you need to be in PASV mode. You can go into PASV mode by declaring
> ftp_pasv($cnx,TRUE);
(PHP 4 >= 4.3.0, PHP 5, PHP 7, PHP 8)
ftp_nb_put — Almacena un archivo en el servidor FTP (modo no-bloqueo)
$ftp_stream,$remote_file,$local_file,$mode,$startpos = 0ftp_nb_put() almacena un archivo local en el servidor FTP.
La diferencia entre esta función y ftp_put() es que esta función carga el archivo de forma asincrónica, de modo que su programa puede realizar otras operaciones mientras el archivo está siendo cargado.
ftp_streamEl identificador de enlace de la conexión FTP.
remote_fileLa ruta del archivo remoto.
local_fileLa ruta del archivo local.
mode
El modo de transferencia. Debe ser FTP_ASCII o
FTP_BINARY.
startposLa posición en el archivo remoto para empezar a subirlo.
Devuelve FTP_FAILED o FTP_FINISHED
o FTP_MOREDATA.
Ejemplo #1 Ejemplo de ftp_nb_put()
<?php
// Iniciar la Carga
$ret = ftp_nb_put($my_connection, "test.remote", "test.local", FTP_BINARY);
while ($ret == FTP_MOREDATA) {
// Haga lo que quiera
echo ".";
// Continuar la carga...
$ret = ftp_nb_continue($my_connection);
}
if ($ret != FTP_FINISHED) {
echo "Hubo un error al cargar el archivo...";
exit(1);
}
?>Ejemplo #2 Reanudación de un proceso de carga con ftp_nb_put()
<?php
// Iniciar
$ret = ftp_nb_put($my_connection, "test.remote", "test.local",
FTP_BINARY, ftp_size("test.remote"));
// O: $ret = ftp_nb_put($my_connection, "test.remote", "test.local",
// FTP_BINARY, FTP_AUTORESUME);
while ($ret == FTP_MOREDATA) {
// Haga lo que quiera
echo ".";
// Continuar la carga...
$ret = ftp_nb_continue($my_connection);
}
if ($ret != FTP_FINISHED) {
echo "Hubo un error al cargar el archivo...";
exit(1);
}
?>
If you receive an error like:
Warning: ftp_nb_put(): Unable to service PORT commands in /path/to/file.php on line 27
verify whether you need to be in PASV mode. You can go into PASV mode by declaring
> ftp_pasv($cnx,TRUE);When using non blocking functions if you try to disconnect while your non blocking operation is in progress the disconnect command will not work until the operation is not finished.Don't add a sleep() inside the loop. If you do you will severely slow down the upload.
In my tests, each time through the loop it send about 2.5K, looping about 220 times per second. (Which is very little.)
You won't necessarily get the same numbers as me per loop, but clearly PHP does it's own management of the loop so that you don't consume all the CPU on the server.How to realize the possibility of transferring data from one FTP-server to another via FXP:
<?php
// ...
$ansver = ftp_raw($ftp_conn1, 'PASV');
if (intval($ansver[0]) == 227) {
ftp_raw($ftp_conn2, 'PORT '.substr($ansver[0], $n = strpos($ansver[0], '(') + 1, strpos($m[0], ')', $n) - $n));
ftp_raw($ftp_conn1, 'STOR '.$filename); // need asynchronously (non-blocking)
ftp_raw($ftp_conn2, 'RETR '.$filename);
}
?>Hi,
I tried to use both ftp_put() and ftp_nb_put() adding the
variable $start = date("Y:m:d h:i:s"); at the begin of the script and the variable $end = date("Y:m:d h:i:s"); at its end, after the file upload function.
With the gprs connection I'm now using and trying to upload a .jpg file of 67,5 kb the time difference between $start and $end was 40 seconds in both cases, so I can suppose that there is no difference between these upload function.
The difference comes if you put anything inside the while ($ftp_upload == FTP_MOREDATA) loop.
I hope this note can help.
RegardsI couldn't see this noted anywhere...
ftp_nb_put apparently takes a much much longer time to upload the file than ftp_put (I haven't done any packet sniffing or logging tests to find out why). I was using a script, nearly identical to the example above, and a 100KB file had only uploaded 3.99KB after about 8 minutes! The php script naturally timed out before it was complete.
I changed my function to use ftp_put, got rid of the loop to check FTP_MOREDATA (as you will see in the example above), and the same script uploaded 2.2MB within 30 seconds with no other changes.
If you're using this function instead of ftp_put *purely to try to speed up your script* and it's taking a long time, you might want to try ftp_put instead.