pclose

(PHP 4, PHP 5, PHP 7, PHP 8)

pclose — Cierra un proceso de un puntero a un fichero

Descripción

pclose(resource $handle): int

Cierra un puntero a un fichero hacia una tubería abierta por popen().

Parámetros

handle: El puntero al fichero debe ser válido, y debe haber sido devuelto por una llamada exitosa a popen().

Valores devueltos

Devuelve el estado de terminación del proceso que se estaba ejecutando. En caso de error, se devuelve -1.

Nota:
Si PHP se compiló con --enable-sigchild, el valor devuelto por esta función es indefinido.

Ejemplos

Ejemplo #1 Ejemplo de pclose()

<?php
$gestor = popen('/bin/ls', 'r');
pclose($gestor);
?>

Notas

Nota: Solamente Unix:

pclose() está internamente implementada usando la llamada al sistema de waitpid(3). Para obtener el código de estado de salida real debería usarse la función pcntl_wexitstatus().

Ver también

popen() - Abre un proceso de un puntero a un fichero

Improve This Page

Learn How To Improve This Page • Submit a Pull Request • Report a Bug

＋add a note

User Contributed Notes 4 notes

down

Uwe Ohse ¶

9 years ago

Regarding the return value:
"Returns the termination status of the process that was run. In case of an error then -1 is returned. "
and the note about the exit status: "pclose() is internally implemented using the waitpid(3) system call. To obtain the real exit status code the pcntl_wexitstatus() function should be used."

The documentation of the return value is, at best, misleading. The function returns, as does proc_close():
* -1 on error,
* WEXITSTATUS(status) if WIFEXITED(status) is true, or 
* status if WIFEXITED(status) is false,
where status is the status parameter of waitpid().

This makes it impossible to differentiate between a relatively normal exit or a termination by signal, and reduces the value of the proc_close return code to a binary one (ok / something broke).

This can be seen in proc_open_rsrc_dtor() in ext/standard/proc_open.c (PHP 5.4.44, 5.6.12). 

The note advising the use of pcntl_wexitstatus is plain wrong. One cannot use pcntl_wexitstatus because it already has been used.

down

vdweij at mailsurf dot com ¶

21 years ago

As I understand pclose will return 0 (on every platform) in case popen could not execute the specified command.

Since popen only returns the status wether it was able to send a command and not wether it was succesfully executed. Only the returned value of pclose can be used to check wether a command could be executed.

down

Mike ¶

16 years ago

The termination status, as pointed out in another note, is not the same as the exit status from the process. However, something like "pclose($fp)/256" is not the correct way to extract the exit status, since this uses system- and version-specific knowledge of where in the termination status the exit status is stored. (Also, the process may not even have exited normally, so it may not have an exit status at all.)

Instead, the functions pcntl_wifexited() and pcntl_wexitstatus() should be used. They are wrappers for the C macros WIFEXITED() and WEXITSTATUS() that are designed for determining whether the process had an exit status and what that status was, respectively.

down

kcross at nssolutions dot com ¶

21 years ago

Somewhere between 4.1.1 and 4.2.3, the return value from pclose changed.

The exit status used to be in the second byte, so that the status would be (pclose($fp)/256).

It is now in the low-order byte, so the status is just pclose($fp).

Be careful.

＋add a note